注册时间2011-6-27
最后登录1970-1-1
在线时间 小时
主题
精华
积分14
贡献
ST
道具劵
|
马上登陆，参与交流。无法注册或登陆请加QQ群：777694204 或Email：admin@cnkeyboard.net
您需要 登录 才可以下载或查看，没有帐号？注册
x
入手YAMAHA YDP161已经两个月了
但弄了这么久还是没搞懂怎么使用软音源
甚至连最基本的USB-MIDI Driver都没安装清楚。。
万恶的YAMAHA居然把驱动下载网址改到不知所谓的地方，找不到了~
感谢ruan斑竹的分享，
https://www.cnkeyboard.com/bbs/thread-111948-1-1.html
说明书也没有中文的，只好自己翻译一下，顺便拿出来分享了
原文：
USB-MIDI Driver Installation (for Windows)
1 Disconnect all USB devices from the computer except for mouse and computer keyboard.
2 start the computer and use the "Administrator" account to log on Windows.
Close all applications and windows that are open.
3 Turn off the power of the instrument.
4 Connect the USB connector of the computer to the USB TO HOST connector of the MIDI instrument with a standard USB cable.
IF your instrument has a HOST SELECT switch, get the switch to "USB".
NOTE Do not use a USB hub for connecting multiple USB devices.
NOTE If you are using several MIDI instruments with USB connection at the same time, connect all the instruments to the computer and turn on the power for all of them, then perform the following installation procedure.
5 Turn on the power of the instrument(s).
6 When the "Found New Hardware wizard" window appears, click [Cancel].
NOTE This screen will not appear on Windows 7. When the message “Device driver software was not successfully installed.” appears, continue the installation procedure.
NOTE If you have already used the instruments via a standard driver in your operating system, this screen will not appear. Go on to the next step.
NOTE On some computers, it may take a few minutes before this screen appears.
7 After the downloaded compressed file is properly extracted, double-click the file “setup.exe.”
The “Preparing to install” window appears. The next window will appear after finishing this preparation.
NOTE (Windows Vista/7) If the “User Account Control” window appears, click [Continue] or [Yes].
8 When the “Welcome to the InstallShield Wizard for Yamaha USB-MIDI Driver” window appears, click [Next].
If the warning message below appears during the installation, click [Yes], [Continue Anyway], or [Install].
9 When a message appears indicating that the driver has been successfully installed, click [Finish].
NOTE On some computers, it may take a few minutes before this screen appears.
10 If a window appears prompting you to restart the computer, do so.
Restart the computer by following the on-screen directions.
Troubleshooting
The driver cannot be installed.
• Is the downloaded driver compatible with your computer?
The 32-bit version of the USB-MIDI Driver is not compatible with a 64-bit OS. Likewise, the 64-bit version of the USB-MIDI Driver is not compatible with a 32-bit OS.
• Is the USB cable connected correctly?
Disconnect the USB cable, then connect it again.
• Is the USB function enabled on your computer? (in Windows)
When you connect the instrument to the computer for the first time, if the “Add (Found) New Hardware Wizard” or the “Found New Hardware” window does not appear, the USB function on the computer may be disabled. Perform the following steps.
1 Select [Control Panel]  [System]  [Hardware]  [Device Manager]
NOTE When using Windows Vista, select [Control Panel]  [Device Manager].
2 Make sure that no “!” or “x” marks appear at “Universal serial bus controller” or “USB Root Hub.”
If you see an “!” or “x” mark, the USB controller is disabled. For details, refer to the owner’s manual for your computer.
• More than ten of MIDI devices are registered in your computer. (Windows)
Due to restrictions in Windows, you can register only up to ten MIDI devices. Also, keep in mind that even when you connect the same specific device to different ports (on different occasions), Windows may recognize that single device as several different devices depending on the port.
If over ten devices have been registered, you cannot install the USB-MIDI Driver, and an error message results.
In this case, try the following operation:
1 Remove the USB-MIDI Driver (page 8), then, install it again.
2 When you installed any driver for MIDI device of other companies, remove a driver for a MIDI device that you do not
use. For details, refer to the manual of the MIDI device.
USB-MIDI 驱动安装方法
1 断开所有连接计算机的USB设备，除了鼠标、键盘。
2 启动电脑并使用Administrator帐户登录WINDOWS。关闭所有应用程序并打开的窗口。
3 关闭乐器的电源。
4 用标准连接线连接计算机的USB接口和MIDI乐器的USB TO HOST接口。（MIDI TO USB连接线应该方法也一样的吧？）
如果你的乐器有一个选择开关，切换到“USB”。
注意:不要使用USB HUB连接多个设备。
注意:如果你使用的是几个电子乐器在同一时间连接，连接所有乐器到计算机，打开所有这些乐器的电源，然后执行下面的安装程序。
5 打开（这些）乐器的电源。
6 当“找到新硬件向导”窗口出现时，点击[取消]。
注意：这个窗口不会出现在Windows 7。当提示“设备驱动软件安装不成功“时，继续安装程序。
注意：如果你使用的乐器在你的操作系统里已经有标准的驱动程序，这个屏幕不会出现。继续下一步。
注意：在有些电脑上，可能需要几分钟时间来等待这个窗口的显示。
7 下载完压缩文件并解压出来后，双击其中的“Setup.exe”。当“Preparing to install”窗口出现后，在下一个窗口出现时完成准备工作。
注意：（Windows Vista/7）如果“用户帐户控制”窗口出现，点击[继续]或[是]。
8 当“Welcome to the InstallShield Wizard for Yamaha USB-MIDI Driver”窗口出现，点击[Next]。
如果在安装时出现警告，点击[Yes](Windows 2000)，[Continue Anyway](Windows XP)或者[Install](Windows Vista/7)。
9 当显示的消息表明该驱动程序已成功安装时，点击[完成]。
注意：在有些电脑上，可能需要几分钟时间来等待这个窗口的显示。
10 如果出现一个窗口，提示您重新启动计算机，请重启。
重新启动计算机后，按照提示进行后续步骤。
疑难解答
驱动程序无法安装。
• 下载的驱动程序与您的电脑兼容吗？
32位版本的usb-midi驱动不兼容的64位操作系统。同样，64位版本的usb-midi驱动程序不兼容的32位操作系统。
• 连接线是否正确连接？
拔出连接线，重新连接一遍。
• 你的电脑启用USB功能了吗？
当你将乐器连接到电脑的第一时间，如果“添加新硬件向导”或“发现新硬件”窗口不出现，计算机的该功能可能被禁用。
执行以下步骤：
1 打开【控制面板】 —【系统】—【硬件】—【设备管理器】。
注意：当使用Windows Vista，选择【控制面板】—【设备管理器】。（没用过Vista，不知道是不是这样。）
2 不要让“！”或“×”的标志出现在“通用串行总线控制器”或“USB Root Hub”。
如果你看到“！”或“×”标记，则该“通用串行总线控制器”被禁用。详情请参考您的计算机的用户手册。
• 十台以上的MIDI设备注册到您的计算机。
由于Windows的限制，你最多可以注册十台MIDI设备。此外，请记住，即使当你连接同一特定装置的不同端口（在不同的场合），Windows会识别单一的设备为几个不同的设备，不同的端口。（没理解这句话想表达什么内容= =！）
如果已经注册超过十台MIDI设备到您的计算机，则您不能安装该usb-midi驱动，并收到错误的消息。
在这种情况下，尝试以下操作：
1 删除usb-midi驱动，然后重新安装。
2 当你安装其他公司的任意一个MIDI的驱动程序时，删除一个你不经常使用的设备的驱动程序。详情参考MIDI设备手册。
|
评分
-
查看全部评分
|
[复制链接]
/2 
发表于 2011-11-30 11:25
置顶卡
变色卡
千斤顶
楼主
发表于 2012-2-11 19:33
